|本期目录/Table of Contents|

[1]韩君,袁祖强,殷晨波,等.倾斜与偏移时轴承动态接触特性分析[J].南京工业大学学报(自然科学版),2019,41(03):338-342.[doi:10.3969/j.issn.1671-7627.2019.03.011]
 HAN Jun,YUAN Zuqiang,YIN Chenbo,et al.Dynamic contact characteristics analysis of bearing exist tilt and deviation[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2019,41(03):338-342.[doi:10.3969/j.issn.1671-7627.2019.03.011]
点击复制

倾斜与偏移时轴承动态接触特性分析()
分享到:

《南京工业大学学报(自然科学版)》[ISSN:1671-7627/CN:32-1670/N]

卷:
41
期数:
2019年03期
页码:
338-342
栏目:
出版日期:
2019-05-28

文章信息/Info

Title:
Dynamic contact characteristics analysis of bearing exist tilt and deviation
文章编号:
1671-7627(2019)03-0338-05
作者:
韩君袁祖强殷晨波张凯
南京工业大学 机械与动力工程学院,江苏 南京 211800
Author(s):
HAN JunYUAN ZuqiangYIN ChenboZHANG Kai
School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211800, China
关键词:
轴承 凸轮 有限元法 偏转角度
Keywords:
bearing cam finite element method tilt and deviation angle
分类号:
TH123.4
DOI:
10.3969/j.issn.1671-7627.2019.03.011
文献标志码:
A
摘要:
以发动机配气机构中凸轮与轴承为研究对象,研究轴颈不同倾斜或偏移角度下滚动轴承与凸轮动态接触问题,分别建立不同倾斜和偏移角下的接触模型。将建模过程通过ANSYS参数化设计语言(APDL)来实现,用显示动力学求解器(LS-DYNA solver)运算对应的K文件,最后在有限元前后处理软件(LS-PrePost)中表征各物理量在整个时域上的变化过程。结果表明:轴颈倾斜角分别为0.1°和0.28°时,轴承外圈上的最大等效应力以及轴上的应力和振动情况并没有特别大的变化; 轴颈相对凸轮偏移1°和2°时,轴承会抱死,轴承和轴上等效应力随着偏移角度的增加而增加; 摇臂轴承上轴承轴颈有小角度倾斜不会引起接触应力大幅度增大; 轴颈偏移一定角度会使轴承接触应力增加; 当轴颈存在偏移的时候,一定范围的倾斜角可以防止抱死。
Abstract:
The dynamic contact problem between rolling bearing and cam was studied from the contact model under different tilt and deviation angles. The modeling calculation was implemented with APDL, the corresponding K files were calculated by LS-DYNA solver, and all physical quantities in the whole time domain was obtained by LS-PrePost. Results showed that when the tilt angle was selected 0.1 and 0.28 degrees, respectively, the maximum equivalent stress on the bearing and vibration and stress on the axis had less changes; when the deviation angle was selected 1 or 2 degrees, the bearing could be locked and force on the bearing and axis would increase with the deviation angle. The small angle tilt of the rocker bearing would not cause the contact stress to increase greatly but the deviation would. The tilt angle could prevent bearing be locked when a little deviation angle existed.

参考文献/References:

[1] 国杰,张文平.内燃机中由配气机构引起的结构振动机理[J].内燃机学报,2017(4):376.
[2] 龚伟,刘权,张青巧,等.增压中冷柴油机摇臂轴承上油结构优化分析[C]//上海“机械工程、热能工程”研究生学术论坛.上海:[s.n.],2014:193.
[3] 周玮,廖日东.高功率密度柴油机主轴承热弹流混合润滑分析[J].内燃机学报,2016(4):370.
[4] 熊万里,周阳,赵紫生,等.高速角接触球轴承套圈倾斜角允许范围的定量研究[J].机械工程学报,2015,51(23):46.
[5] 白晓波,吉晓民,郭磊.内外圈轴线相对倾斜时的滚针轴承载荷分布研究[J].机械强度,2014(2):216.
[6] ZHANG X,HAN Q,PENG Z,et al.A new nonlinear dynamic model of the rotor-bearing system considering preload and varying contact angle of thebearing[J].Communications in Nonlinear Science & Numerical Simulation,2015,22(1/2/3):821.
[7] 余光伟,冒海培,陈飞平,等.基于ANSYS/LS-DYNA的B-1416滚针轴承动力学仿真与分析[J].现代制造工程,2015(5):66.
[8] KOROLEV A V,KOROLEV A A,KREHEL R.Mathematical simulation and analysis of rolling contact fatigue damage in rollingbearings[J].International Journal of Advanced Manufacturing Technology,2017,89(1/2/3/4):1.
[9] 童宝宏,刘颖,程新明,等.轴颈倾斜时滚柱轴承动态接触特性的有限元分析[J].农业工程学报,2012,28(13):42.
[10] 高学海,黄筱调,王华,等.双排四点接触球转盘轴承滚道接触压力分布[J].南京工业大学学报(自然科学版),2011,33(1):80.
[11] HARRIS T A,KOTZALAS M N.滚动轴承分析[M].罗继伟,马伟,译.北京:机械工业出版社,2009.

备注/Memo

备注/Memo:
收稿日期:2018-03-16
基金项目:国家自然科学基金(51575255); 江苏省质量技术监督局科技项目(KJ175914)
作者简介:韩君(1992—),男,E-mail:1226258931@qq.com; 袁祖强(联系人),教授,E-mail:978536929@qq.com.
引用本文:韩君,袁祖强,殷晨波,等.倾斜与偏移时轴承动态接触特性分析[J].南京工业大学学报(自然科学版),2019,41(3):338-342..
更新日期/Last Update: 2019-05-30