|本期目录/Table of Contents|

[1]曹世山,张大长,高正平.单角钢轴压承载力试验对比及理论分析[J].南京工业大学学报(自然科学版),2017,39(03):108-113.[doi:10.3969/j.issn.1671-7627.2017.03.019]
 CAO Shishan,ZHANG Dachang,GAO Zhenping.Experiemental and analytical research on axial bearing capacity of single steel angles[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2017,39(03):108-113.[doi:10.3969/j.issn.1671-7627.2017.03.019]
点击复制

单角钢轴压承载力试验对比及理论分析()
分享到:

《南京工业大学学报(自然科学版)》[ISSN:1671-7627/CN:32-1670/N]

卷:
39
期数:
2017年03期
页码:
108-113
栏目:
出版日期:
2017-05-20

文章信息/Info

Title:
Experiemental and analytical research on axial bearing capacity of single steel angles
文章编号:
1671-7627(2017)03-0108-06
作者:
曹世山1张大长1高正平2
1.南京工业大学 土木工程学院,塔桅结构工程研究中心,江苏 南京 211800; 2.江苏省电力公司经济技术研究院,江苏 南京 210005
Author(s):
CAO Shishan1ZHANG Dachang 1GAO Zhenping 2
1.Research Center of Tower Mast Structure,College of Civil Engineering,Nanjing Tech University,Nanjing 211800,China; 2.State Grid Jiangsu Electric Power Company,Nanjing 210005,China
关键词:
单角钢 轴压承载力试验 有限元模拟 轴压承载力计算公式
Keywords:
steel single angle experiment of axial bearing capacity finite element simulation calculation formula of axial bearing capacity
分类号:
TU392.3
DOI:
10.3969/j.issn.1671-7627.2017.03.019
文献标志码:
A
摘要:
国外线路工程按照ASCE 10-97设计,EPRI及SERC铁塔测试中心发现用该规范设计的铁塔失效概率为23%; 而按照国标杆塔规范设计的输电塔经济指标过高。因此,有必要开展单角钢的轴压承载力试验,进一步提出合理的单角钢承载力设计方法。本文选取18根单角钢进行轴压承载力试验及有限元分析,考虑所用刀铰装置的有效计算长度系数,确定单角钢的轴压稳定承载力。随后,提出一个综合考虑长细比和宽厚比的轴压稳定承载力计算公式,并验证了其适用性,为国外线路工程杆塔设计提供可靠的依据。
Abstract:
Foreign transmission line project reported that the failure rate of tower which designed by ASCE 10-97 was 23% in the EPRI and SERC,in the meantime,prototype tower in accordance with DL/T 5154 may often be too expensive.Therefore,it is necessary to carry out the axial bearing capacity test of single steel angle and a new rational calculation equation for designing of steel angles.Axial bearing capacity tests and FEM simulations of single angles were carried out in this paper,considering the effective length factor of the knife hinge adopted here,it revealed the true axial bearing capacity of single angle.Subsequently,this paper proposed a comprehensive design practice for bearing capacity of axial compressed single angle with slenderness ratio and width to thickness ratio,and the suitability of the proposed calculation method was validated.The proposed method can be used for foreign transmission line engineering design for its simplicity.

参考文献/References:

[1] American society of civil engineers.Design of latticed steel transmission structures[S].Virginia:American Society of Civil Engineers 1801 Alexander Bell Drive Reston,1997.
[2] International electrotechnical commission.Loading test on overhead line structures[S].British:International Electrotechnical Commission Publication,2002.
[3] LEMASTER R.A.In innovations in the design of electrical transmission structures[R].Virginia:American Society of Civil Engineers,1985.
[4] MOHAN S J,PRASAD R N,LAKSHMANAN N.Flexural and local buckling interaction of steel angles [J].International journal of structural stability and dynamics,2005,5(2):143.
[5] 中华人民共和国国家经济贸易委员会.架空送电线路杆塔结构设计技术规定:DL/T S154—2002[S].北京:中国电力出版社,2002.
[6] WAKABAYASHI M.On the buckling strength of angles in transmission towers[J].Bulletin of disaster prevention research institute,1965,15(91):1.
[7] AL-SAYED S H,BJORHOVDE R.Experimental study of single angle column[J].Construct steel research,1989,12(1):83.
[8] BATHON L.Ultimate load capacity of single steel angles[J].Journal of structural engineering,1993,119(1):279.
[9] ALDURI S M R,MADUGULA M R S.Flexural buckling of steel angles:experimental investigation[J].ASCE,122(3):309.
[10] SINGER J.On the applicability of the southwell plot to plastic buckling[J].Experimental mechanics,1989,29(2):205.
[11] BSI standards pulication.Overhead electrical lines exceeding AC 45 kV[S].British:European Publications,2002.
[12] SUN J,JOHN W.Butterworth.Behavior of steel single angle compression members axially loaded through one leg[J].The alliance for scientific editing in China,2004,98:859.
[13] 中国工程建设标准化协会.钢结构设计规范:GB 50017—201X[S].北京:中国计划出版社,2014.
[14] ZIEMIAM D.Guide to stability design criteria for metal structrues[M].Hoboken:John Wiley,2010.

备注/Memo

备注/Memo:
收稿日期:2016-02-21
基金项目:江苏省科技厅前瞻性联合研究项目(BY2014005-11)
作者简介:曹世山(1990—),男,江苏南京人,硕士,主要研究方向为钢结构; 张大长(联系人),教授,E-mail: dczhangchina@163.com.
引用本文:曹世山,张大长,高正平.单角钢轴压承载力试验对比及理论分析[J].南京工业大学学报(自然科学版),2017,39(3):108-113..
更新日期/Last Update: 2017-05-31