|本期目录/Table of Contents|

[1]陈立立,顾伯勤,张斌,等.芳纶纤维表面涂层制备及其黏弹性表征[J].南京工业大学学报(自然科学版),2016,38(03):19-24.[doi:10.3969/j.issn.1671-7627.2016.03.004]
 CHEN Lili,GU Boqin,ZHANG Bin,et al.Preparation and viscoelasticity characterization of aramid fiber with surface coating[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2016,38(03):19-24.[doi:10.3969/j.issn.1671-7627.2016.03.004]
点击复制

芳纶纤维表面涂层制备及其黏弹性表征()
分享到:

《南京工业大学学报(自然科学版)》[ISSN:1671-7627/CN:32-1670/N]

卷:
38
期数:
2016年03期
页码:
19-24
栏目:
出版日期:
2016-05-28

文章信息/Info

Title:
Preparation and viscoelasticity characterization of aramid fiber with surface coating
文章编号:
1671-7627(2016)03-0019-06
作者:
陈立立顾伯勤张斌宇晓明姜剑
南京工业大学 机械与动力工程学院,江苏 南京 211800
Author(s):
CHEN LiliGU BoqinZHANG BinYU XiaomingJIANG Jian
College of Mechanical and Power Engineering,Nanjing Tech University,Nanjing 211800,China
关键词:
复合材料 纤维增强 界面 黏弹性 松弛
Keywords:
composite fiber-reinforced interface viscoelasticity relaxation
分类号:
TB332
DOI:
10.3969/j.issn.1671-7627.2016.03.004
文献标志码:
A
摘要:
为了近似表征芳纶纤维增强橡胶复合材料界面的黏弹性性能,制备了不同胶乳含量的间苯二酚甲醛-丁苯吡胶乳共混(RFL)胶膜。实验研究了胶膜的拉伸性能和松弛性能。分别采用基于Burgers模型的单向拉伸和三维各向同性理论模型表征松弛模量,并拟合得到理论模型的参数。实验结果表明,胶膜的拉伸力学行为具有明显的非线性特征。不同胶乳含量下,胶膜的松弛规律相同,松弛模量初时下降较快,之后迅速趋于平稳。RFL胶膜的静态性能随着胶乳含量的增加而降低,抗松弛性能随胶乳含量的增加而先增后减,合适的预缩合酚醛树脂-丁苯吡胶乳(RF/L)干质量比约为24:100。胶膜的2种理论模型均能较好地表征胶膜松弛的初始阶段,但在试验0.5 h后理论拟合的松弛速率与实验有明显差异。提出了胶膜三维各向同性理论模型中体积模量的估算方法,选取主弹性模量稳定值的1.01倍对应的体积模量作为计算依据。
Abstract:
In order to characterize the viscoelasticity property of reinforced rubber composites interface of aramid fiber,the resorcinol formaldehyde-butadiene styrene vinyl-pyridine rubber latex(RFL)adhesive films with different contents of latex were prepared. Tensile and relaxation property of adhesive films were investigated experimentally. The relaxation modulus was characterized by uniaxial tension and three-dimensional isotropic models based on Burgers model respectively,and the parameters of Burgers model were obtained. Results showed that tensile mechanical behavior of the film was nonlinear. Relaxation modulus of films with different contents of latex could be correlated with the same relaxation law and declined faster at the beginning,and then quickly leveled off. The static mechanical properties of RFL adhesive films weakened as the content of latex increased. The anti-relaxation property first increased and then decreased with the increase in the content of latex. The optimal value was obtained when dry mass ratio of precondensed phenolic resin-pyridine-styrene-butadiene rubber latex(RF/L)reached 24:100. Both theoretical models characterized the initial stage of relaxation process of adhesive film appropriately,but there were significant differences between the relaxation rate fitted theoretically and experimental data obtained 0.5 h after the experiment. With the proposed method to estimate bulk modulus of three-dimensional isotropic model of film,1.01 times of the stable elasticity was selected as the calculation basis.

参考文献/References:

[1] GU B,CHEN Y,ZHOU J.Design,manufacture and performance evaluation of non-asbestos sealing composites[J].Advances in composite materials-ecodesign and analysis,2011(1):21.
[2] GU B Q,CHEN Y.Development of a new kind of sealing composite material reinforced with aramid and pre-oxidized fibers[J].Key engineering materials,2007,353:1243.
[3] 朱大胜,顾伯勤,陈晔.短纤维增强橡胶基密封复合材料细观结构参数及其界面力学行为研究[J].润滑与密封,2008(6):93.
[4] 朱大胜,顾伯勤,陈晔.纤维增强弹性体基复合材料单纤维拔出试验细观力学分析[J].工程力学,2009(5):1.
[5] QU M,DENG F,KALKHORAN S M,et al.Nanoscale visualization and multiscale mechanical implications of bound rubber interphases in rubber-carbon black nanocomposites[J].Soft matter,2011,7(3):1066.
[6] ZHANG J,GUO Q,HUSON M,et al.Interphase study of thermoplastic modified epoxy matrix composites:phase behaviour around a single fibre influenced by heating rate and surface treatment[J].Composites part A:applied science and manufacturing,2010,41(6):787.
[7] 杨仲.考虑界面相的单向复合材料力学性能预报研究[D].哈尔滨:哈尔滨工业大学,2010.
[8] ALLEN K W.Silanes as the interphase in adhesive bonds[J].Journal of adhesion science and technology,1992,6(1):23.
[9] 申明霞,费传军,夏涛,等.芳纶纤维表面涂覆层组成及其力学性能关系研究[J].玻璃钢/复合材料,2006(4):20.
[10] 邵俊华.玻璃纤维沥青混合料黏弹性分析及参数确定[D].长春:吉林大学,2008.
[11] 叶永,杨新华,陈传尧.沥青砂黏弹性模型参数的试验研究[J].中外公路,2009(4):192.
[12] 申明霞,李红香,杨开宇,等.芳纶纤维表面处理与浸渍工艺研究[J].材料开发与应用,2008(1):41.
[13] 张辉,申明霞,覃小红,等.玻璃纤维线绳用RFL胶膜成膜性能及撕裂性能的研究[J].橡胶工业,2004,51(10):607.

相似文献/References:

[1]王晓东,朱辅华,黄培.聚酰亚胺聚四氟乙烯复合材料的制备和表征[J].南京工业大学学报(自然科学版),2011,33(04):16.[doi:10.3969/j.issn.1671-7627.2011.04.004]
 WANG Xiaodong,ZHU Fuhua,HUANG Pei.Preparation and characterization of PI-PTFE compsite materials[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2011,33(03):16.[doi:10.3969/j.issn.1671-7627.2011.04.004]
[2]朱波,周叮,刘伟庆.芯材增强对夹层圆柱壳屈曲性能的影响[J].南京工业大学学报(自然科学版),2011,33(05):100.[doi:10.3969/j.issn.1671-7627.2011.05.020]
 ZHU Bo,ZHOU Ding,LIU Weiqing.Effects of reinforcement on buckling of composite cylindrical shells[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2011,33(03):100.[doi:10.3969/j.issn.1671-7627.2011.05.020]
[3]李传江,顾伯勤,黄星路.横向压缩载荷下短纤维复合材料细观力学分析[J].南京工业大学学报(自然科学版),2012,34(02):120.[doi:doi:10.3969/j.issn.1671-7627.2012.02.025]
 LI Chuanjiang,GU Boqin,HUANG Xinglu.Micromechanics analysis of short fiber-reinforced composites under transverse compressive loads[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2012,34(03):120.[doi:doi:10.3969/j.issn.1671-7627.2012.02.025]
[4]崔运国,陆春华,张军,等.纳米SiO2/PMMA复合材料的光学性能[J].南京工业大学学报(自然科学版),2012,34(04):101.[doi:10.3969/j.issn.1671-7627.2012.04.020]
 CUI Yunguo,LU Chunhua,ZHANG Jun,et al.Optical properties of nano-SiO2/PMMA composite material[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2012,34(03):101.[doi:10.3969/j.issn.1671-7627.2012.04.020]
[5]宋艳江,章刚,朱鹏,等.玻璃纤维改性热塑性聚酰亚胺复合材料弯曲性能 (Ⅰ)——热处理工艺影响[J].南京工业大学学报(自然科学版),2008,30(02):15.[doi:10.3969/j.issn.1671-7627.2008.02.004]
 SONG Yan-jiang,ZHANG Gang,ZHU Peng,et al.Bending strength of TPI GF composites (Ⅰ) -influence of heat treatment[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2008,30(03):15.[doi:10.3969/j.issn.1671-7627.2008.02.004]
[6]徐洁,盛绪敏.陶瓷基质—SiC晶须复合材料[J].南京工业大学学报(自然科学版),1990,12(04):81.
 Xu Jie Sheng Xumin(Department of Silicate Engineering).CERAMIC MATRIX-SiC WHISKER COMPOSITES[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),1990,12(03):81.
[7]程可,马功勋.纤维增强复合梁Ⅰ型裂纹尖端凝合区模型[J].南京工业大学学报(自然科学版),1998,20(04):94.
 Cheng Ke Ma Gongxun Department of Mechanical Engineering,Nanjing University of Chemical Technology,Nanjing0009,et al.MODEL FOR COHESIVE ZONE OF TOP OF TYPE Ⅰ CRACK IN FIBRE REINFORCED COMPOSITE BEAM[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),1998,20(03):94.
[8]王志远,沈 旭,俞 娟,等.纳米炭黑/聚酰亚胺复合材料在不同工况条件下的摩擦磨损性能[J].南京工业大学学报(自然科学版),2015,37(02):18.
 WANG ZhiyuanSHEN XuYU JuanGU HepingWANG XiaodongHUANG Pei.Friction and wear performance of nanometer carbon black/polyimide composite material on different working conditions[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2015,37(03):18.
[9]张富宾,刘伟庆,齐玉军,等.腹板对复合材料夹层梁抗扭性能影响分析[J].南京工业大学学报(自然科学版),2015,37(01):70.[doi:10.3969/j.issn.1671-7627.2015.01.013]
 ZHANG Fubin,LIU Weiqing,QI Yujun,et al.Torsion analysis on composite sandwich beams with web configurations[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2015,37(03):70.[doi:10.3969/j.issn.1671-7627.2015.01.013]
[10]马亚利,王璐,欧谨,等.温度荷载作用下GFRP-泡沫夹层结构Ⅱ型界面断裂韧性分析[J].南京工业大学学报(自然科学版),2017,39(03):90.[doi:10.3969/j.issn.1671-7627.2017.03.016]
 MA Yali,WANG Lu,OU Jin,et al.Analysis of modeⅡ interfacial fracture toughness of GFRP-foam sandwich structure under temperature loading[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2017,39(03):90.[doi:10.3969/j.issn.1671-7627.2017.03.016]

备注/Memo

备注/Memo:
收稿日期:2015-01-08
基金项目:国家自然科学基金(51375223); 江苏省普通高校研究生科研创新计划(KYZZ15_0230)
作者简介:陈立立(1991—),男,江苏靖江人,博士生,主要研究方向为流体密封与测控技术; 顾伯勤(联系人),教授,E-mail:bqgu@njtech.edu.cn.
引用本文:陈立立,顾伯勤,张斌,等.芳纶纤维表面涂层制备及其黏弹性表征[J].南京工业大学学报(自然科学版),2016,38(3):19-24..
更新日期/Last Update: 2016-05-20