|本期目录/Table of Contents|

[1]宇晓明,邵春雷,顾伯勤.叶轮切割方式对IS 100-65-200型离心泵性能的影响[J].南京工业大学学报(自然科学版),2013,35(01):1-109.[doi:10.3969/j.issn.1671-7627.2013.01.023]
 YU Xiaoming,SHAO Chunlei,GU Boqin.Effects of impeller cutting ways on performances of IS 100-65-200 type centrifugal pump[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2013,35(01):1-109.[doi:10.3969/j.issn.1671-7627.2013.01.023]
点击复制

叶轮切割方式对IS 100-65-200型离心泵性能的影响()
分享到:

《南京工业大学学报(自然科学版)》[ISSN:1671-7627/CN:32-1670/N]

卷:
35
期数:
2013年01期
页码:
1-109
栏目:
出版日期:
2013-01-20

文章信息/Info

Title:
Effects of impeller cutting ways on performances of IS 100-65-200 type centrifugal pump
文章编号:
1671-7627(2013)01-0109-05
作者:
宇晓明邵春雷顾伯勤
南京工业大学 机械与动力工程学院,江苏 南京 211800
Author(s):
YU Xiaoming SHAO Chunlei GU Boqin
College of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 211800, China
关键词:
离心泵 正切 斜切 切割定律 切割公式
Keywords:
centrifugal pump straight cut miscut cutting law cutting formula
分类号:
TB42
DOI:
10.3969/j.issn.1671-7627.2013.01.023
文献标志码:
A
摘要:
采用Fluent软件在双参考坐标系下,利用有限体积法对雷诺时均Navier Stokes方程进行数值离散,选用标准k-ε湍流模型,SIMPLEC方法求解,对IS 100-65-200型离心泵在不同叶轮切割方式下的内部流场进行了叶轮和蜗壳的耦合数值模拟。根据数值模拟结果预测IS 100-65-200型离心泵的性能,并分析不同叶轮切割方式对泵内部流场的影响。结果表明:泵的扬程、轴功率和效率受切割方式的影响明显,相同切割量下,随着切割角度的增加,扬程先升高后降低,切割角度θ在0°~20°的范围内扬程达到最高; 轴功率先升高后降低,θ在20°左右时达到最高。反向斜切达到的最高效率和扬程明显高于正切和正向斜切,正向斜切达到的最高轴功率明显高于反向斜切和正切。内部流场分析表明:在相同外特性下,反向斜切时叶轮内低压区面积小于正切和正向斜切,提高了泵的性能,同时,反向斜切减小了隔舌处的回流,提高了泵的效率。不同切割方式下,切割前后叶轮出口相应位置处速度三角形并不相似。考虑切割角度的大小,对现有切割公式进行了修正和验证。
Abstract:
In different cutting ways, the flow field in 100-65-200 type centrifugal pump was simulated by Fluent software. The standard k-ε turbulence model and SIMPLEC algorithm were chosen in FLUENT. The simulation was steady and the moving reference frame was used to consider rotor-stator interaction. According to the simulation results, effects on the internal flow in 100-65-200 type centrifugal pump with different impeller cutting ways were analyzed and the performances of the centrifugal pump were predicted. The results showed that the head, the shaft power and the efficiency of the pump were affected by the cutting way. With the increasing of the cutting angle, the head and the power were increased at first and then decreased on the same cutting value. When the cutting angle was from 0° to 20°, the head value reached the highest one. When the cutting angle was about 20°, the power value reached the highest one. The highest efficiency and the head in the reverse miscut were obviously higher than that in the straight cut and positive miscut. The highest shaft power in the positive miscut was obviously higher than that in the reverse miscut way and straight miscut. The the inner flow analysis results indicated that, with the same external characteristics, the low-pressure area of the reverse miscut in the impeller was smaller than the tangent and the positive miscut, so the centrifugal pump performance was improved. Meanwhile, the reverse miscut reduced backflow at the tongue and enhanced the efficiency of the pump. In different cutting ways, the speed triangles at corresponding position of impeller outlet were not similar before and after impeller cutting. Considering different cutting angles, the existing cutting formula was revised and verified.

参考文献/References:

[1] Barrio R,Blanco E,Parrondo J,et al.The effect of impeller cut back on the fluid-dynamic pulsations and load at the blade-passing frequency in a centrifugal pump[J].Journal of Fluid Engineering,2008,130(11):111102-1-111102-11.
[2] Gonzlez J,Parrondo J,Santolaria C,et al.Steady and unsteady radial forces for a centrifugal pump with impeller to tongue gap variation[J].Journal of Fluids Engineering,2006,128(3):454-462.
[3] Stan S.When trimming a centrifugal pump impeller can save energy and increase flow rate[J].World Pumps,1999(398):37-40.
[4] Mario ,Hrvoje K,Igor S,et al.Improving centrifugal pump efficiency by impeller trimming[J].Desalination,2009,249(2):654-659.
[5] 谈明高,刘厚林,王勇,等.叶轮外径对离心泵内流影响的CFD分析[J].排灌机械,2009,27(5):314-318.
[6] 胡彬彬,王春林,阮劲松,等.低比转数离心泵叶轮切割定律的研究[J].农机化研究,2005(5):81-82.
[7] 张爱霞.低比速离心泵叶轮切割实践[J].水泵技术,2004(5):37-38.
[8] 李宁.叶轮切割理论在循环氨水泵节能改造中的应用[J].流体机械,2008,36(12):45-48.
[9] 董量,谈明高,王勇,等.转速对离心泵内部流动的影响[J].农机化研究,2009(11):49-51.
[10] 关醒凡.现代泵技术手册[M].北京:宇宙出版社,1995.
[11] 谈明高.离心泵能量性能预测的研究[D].镇江:江苏大学,2008.

相似文献/References:

[1]宦月庆,邵春雷,黄星路,等.中比转数离心泵内部流场的三维数值模拟[J].南京工业大学学报(自然科学版),2010,32(02):42.
 HUAN Yue-qing,SHAO Chun-lei,HUANG Xing-lu,et al.3D numerical simulation on internal flow field in medium specific speed centrifugal pump[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2010,32(01):42.
[2]江振兴,顾伯勤,邵春雷.基于现有蜗壳的高效低噪叶轮设计及数值分析[J].南京工业大学学报(自然科学版),2013,35(05):114.[doi:10.3969/j.issn.1671-7627.2013.05.022]
 JIANG Zhenxing,GU Boqin,SHAO Chunlei.Design and numerical analysis on impeller with high efficiency and low noise based on existing volute[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2013,35(01):114.[doi:10.3969/j.issn.1671-7627.2013.05.022]
[3]郝英杰,顾伯勤,邵春雷.叶轮切割方式对离心泵外特性和压力脉动的影响[J].南京工业大学学报(自然科学版),2015,37(05):42.[doi:10.3969/j.issn.1671-7627.2015.05.007]
 HAO Yingjie,GU Boqin,SHAO Chunlei.Effects of impeller cutting ways on external performances and pressure fluctuation characteristics of centrifugal pump[J].Journal of NANJING TECH UNIVERSITY(NATURAL SCIENCE EDITION),2015,37(01):42.[doi:10.3969/j.issn.1671-7627.2015.05.007]

备注/Memo

备注/Memo:
收稿日期:2012-04-23
基金项目:江苏省高校自然科学研究项目(10KJB470006)
作者简介:宇晓明(1986—),女,吉林吉林人,硕士,主要研究方向为流体工程与流体密封技术; 顾伯勤(联系人),教授,E-mail:bqgu@njut.edu.cn..
更新日期/Last Update: 2013-01-20